If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
My Minolta C6100 is getting paper Jams at the M3 section, its not getting past that section, is there a solution for this, I got an error code of C-0130 when doing the paperless run test.
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
The C-0130 is a PF-707m roller pressure release abnormality.
With larger media, rather than maintaining a buckle between the rollers of the paper pickup unit, this paper feeder releases the pinch roller pressure to allow the media to pull through.
I had this erro on a bizhub C1060:
"C0130" error message, with PF-707, won't clear.
Roller pressure release motor M10 cannot reach home position. Clean roller pressure release sensor PS41 (was heavily caked with translucent grease). When cleaned, machine comes to ready. It feeds a few sheets before coding out with loud gear noise. The 2nd tooth from the flat on sector gear 36T is worn/flattened.
Clean roller pressure release sensor PS41 in a cup of alcohol. Replace release cam (A55C 7137 00), and release sector gear 36T (A55C 7195 00).
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
The C-0130 is a PF-707m roller pressure release abnormality.
With larger media, rather than maintaining a buckle between the rollers of the paper pickup unit, this paper feeder releases the pinch roller pressure to allow the media to pull through.
I had this erro on a bizhub C1060:
"C0130" error message, with PF-707, won't clear.
Roller pressure release motor M10 cannot reach home position. Clean roller pressure release sensor PS41 (was heavily caked with translucent grease). When cleaned, machine comes to ready. It feeds a few sheets before coding out with loud gear noise. The 2nd tooth from the flat on sector gear 36T is worn/flattened.
Clean roller pressure release sensor PS41 in a cup of alcohol. Replace release cam (A55C 7137 00), and release sector gear 36T (A55C 7195 00).
Is There some diagram or pictures of what I should look for?
Respectfully, you might take a look at the service manual. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
The C-0130 is a PF-707m roller pressure release abnormality.
With larger media, rather than maintaining a buckle between the rollers of the paper pickup unit, this paper feeder releases the pinch roller pressure to allow the media to pull through.
I had this erro on a bizhub C1060:
"C0130" error message, with PF-707, won't clear.
Roller pressure release motor M10 cannot reach home position. Clean roller pressure release sensor PS41 (was heavily caked with translucent grease). When cleaned, machine comes to ready. It feeds a few sheets before coding out with loud gear noise. The 2nd tooth from the flat on sector gear 36T is worn/flattened.
Clean roller pressure release sensor PS41 in a cup of alcohol. Replace release cam (A55C 7137 00), and release sector gear 36T (A55C 7195 00).
I bow before thee.
Adversity temporarily visits a strong man but stays with the weak for a lifetime.
One more quick question if the machine isn't leveled correct? can i get a paperjam?, or that has nothing to do with it?
It's unrelated to leveling. It's a simple mechanical issue that you won't see until you do some disassembly.
And the C-0130 is and error code, not a jam code. There is a difference. =^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
CN118 of PFUDB, CN432 (relay connector), CN433 (relay connector), CN437 (relay connector), CN410 of PS40, and the wiring between PFUDB and PS40. Then, repair it when there is any abnormality.
5. Replace PS40.
6. Replace PFUDB.
Table 1: Result check
Result check
Normal
Abnormal
START
About 4500
65535
Deviate from "normal" significantly
STOP
About 4500
65535
Deviate from "normal" significantly
Faulty part isolation DIPSW
Control while detached
We know a thing or two because we've seen a thing or two.
The medication helps though...
CN118 of PFUDB, CN432 (relay connector), CN433 (relay connector), CN437 (relay connector), CN410 of PS40, and the wiring between PFUDB and PS40. Then, repair it when there is any abnormality.
5. Replace PS40.
6. Replace PFUDB.
Table 1: Result check
Result check
Normal
Abnormal
START
About 4500
65535
Deviate from "normal" significantly
STOP
About 4500
65535
Deviate from "normal" significantly
Faulty part isolation DIPSW
Control while detached
I seem to recall that the centering sensor assembly must be installed when the PF707m is used on a C6100.
=^..^=
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
Comment